- Thu Feb 17, 2011 12:43 pm
#239067
A build I might consider, I got to say, Australia builds some pretty awesome cars
Spec:
Engine bay / performance:
-B16B head + B18CR block
B18CR crank + rods, OS 81.25 CTR pistons, ACL race bearings, OEM headgasket, Toda camgears, CTR cams + valve springs, Mugen thermostat + fan switch, Dizzy
-EK9 LSD gearbox
-ORC 309 single plate clutch w/ lightweight flywheel
-Mfactory 4.928 final drive
-Apexi PowerFC ECU with handheld
-Injen intake
-Honda B18CR intake manifold and throttle body
-Koyo radiator
-Hytec tri-y replica big tube header
-Hasport engine mounts
-Custom 2.5" exhaust
-Oil cooler kit
-Custom baffled oil pan
-Power steering deleted
-Aircon deleted
-Wire tucked
-Engine bay sprayed in metalic gunmetal
-Tuned by IS motoring. Pulling 127kw atw
Handling:
-Buddyclub racing spec coilovers
-Buddyclub front and rear camber kit
-Custom front castor
-Wilwood big brake kit (front)
-EK4 rear brakes (rear) with Project Mu pads
-Buddyclub QF forged 15x7 wheels with Toyo semis
-Ultra racing 3 point front strut
-Ultra racing 4 point rear strut
-Ultra racing 3 point fender bar
-DC2R subframe
-DC2R front and rear sway
-ASR rear reinforcement
-All bushings checked 3mths ago and broken one replaced with Honda genuine products (real trailing arm is Mugen)
-Corner weighted and wheel alignment performed by Heasman Steering
Exterior:
-JDMyard Carbon fiber bonnet
-Genuine Spoon Carbon fiber mirrors
-Genuine Spoon Carbon fiber wing
-Genuine Spoon decals
-Genuine Spoon wipers
-Exterior resprayed in Phoenix Yellow 3 mths ago by professional
-Window Tinted 2 months ago
-Honda OEM window visor
-Number plate SP00NB
Interior:
-Bride Zeta III sport bucket seat (Driver)
-Bride style reclinable seat (Passenger)
-Momo competition steering wheel
-Work Bell quick release steering hub
-Honda JDM EG6 cluster
-Mugen gearknob
-Honda OEM DC2R pedals
-Interior sprayed in metalic gunmetal
-Protected by a good alarm system
-All stock interior trims and seats will be provided (except stock driver seat)
Condition:
Immaculate condition inside and out.
Mechanical A+++++.
Never involved in any accidents in my hands.
All panels and the chassis are straight, all small dents and couple of nicks were repaired before resprayed.
All seals replaced / reconditioned after resprayed.
No rust! No leaks! Always serviced by Top One in Arncliffe.
Chassis done 18xxxx km
Engine only 12000km
Gearbox reconditioned + 4.928 final drive installed only 1000km ago.
Just renewed rego till Nov 09
Spec:
Engine bay / performance:
-B16B head + B18CR block
B18CR crank + rods, OS 81.25 CTR pistons, ACL race bearings, OEM headgasket, Toda camgears, CTR cams + valve springs, Mugen thermostat + fan switch, Dizzy
-EK9 LSD gearbox
-ORC 309 single plate clutch w/ lightweight flywheel
-Mfactory 4.928 final drive
-Apexi PowerFC ECU with handheld
-Injen intake
-Honda B18CR intake manifold and throttle body
-Koyo radiator
-Hytec tri-y replica big tube header
-Hasport engine mounts
-Custom 2.5" exhaust
-Oil cooler kit
-Custom baffled oil pan
-Power steering deleted
-Aircon deleted
-Wire tucked
-Engine bay sprayed in metalic gunmetal
-Tuned by IS motoring. Pulling 127kw atw
Handling:
-Buddyclub racing spec coilovers
-Buddyclub front and rear camber kit
-Custom front castor
-Wilwood big brake kit (front)
-EK4 rear brakes (rear) with Project Mu pads
-Buddyclub QF forged 15x7 wheels with Toyo semis
-Ultra racing 3 point front strut
-Ultra racing 4 point rear strut
-Ultra racing 3 point fender bar
-DC2R subframe
-DC2R front and rear sway
-ASR rear reinforcement
-All bushings checked 3mths ago and broken one replaced with Honda genuine products (real trailing arm is Mugen)
-Corner weighted and wheel alignment performed by Heasman Steering
Exterior:
-JDMyard Carbon fiber bonnet
-Genuine Spoon Carbon fiber mirrors
-Genuine Spoon Carbon fiber wing
-Genuine Spoon decals
-Genuine Spoon wipers
-Exterior resprayed in Phoenix Yellow 3 mths ago by professional
-Window Tinted 2 months ago
-Honda OEM window visor
-Number plate SP00NB
Interior:
-Bride Zeta III sport bucket seat (Driver)
-Bride style reclinable seat (Passenger)
-Momo competition steering wheel
-Work Bell quick release steering hub
-Honda JDM EG6 cluster
-Mugen gearknob
-Honda OEM DC2R pedals
-Interior sprayed in metalic gunmetal
-Protected by a good alarm system
-All stock interior trims and seats will be provided (except stock driver seat)
Condition:
Immaculate condition inside and out.
Mechanical A+++++.
Never involved in any accidents in my hands.
All panels and the chassis are straight, all small dents and couple of nicks were repaired before resprayed.
All seals replaced / reconditioned after resprayed.
No rust! No leaks! Always serviced by Top One in Arncliffe.
Chassis done 18xxxx km
Engine only 12000km
Gearbox reconditioned + 4.928 final drive installed only 1000km ago.
Just renewed rego till Nov 09
)
)