Civic-EG.com Forum 3.3.1

- Mon Aug 25, 2014 7:00 pm #348243 When I rebuilt my engine i replaced all gaskets and seal. Last night i removed the vc and cleaned it and made sure it was not cracked or was seating wrong. And I check this morning after my drive to work and still leaking. can i use gasket maker to help seal it off untill i get a oem honda one? Or am i just gonna leak for 2 weeks lol. I just replaced oil and filter. Its the only thing that is wrong since rebuild. So I guess it could be worse.

Hatch http://civic-eg.com/viewtopic.php?t=27660
Sedan(gone) http://civic-eg.com/viewtopic.php?t=7462

[teal_dx]

- Mon Aug 25, 2014 7:19 pm #348244 What area is it leaking from?
I've put a tiny bit of Honda Bond in the corners by the cam cutouts and that helped. They seem to leak from there a lot.

Do Not PM me your technical questions. Post them in the forum!
My 1992 SOHC Turbo Hatch
My Youtube Channel: 6th Gear Garage

- Mon Aug 25, 2014 7:21 pm #348245 If you are looking at the engine it is on the left front corner. I used the bond on the corner where it leaks normally. It only in the front.

Hatch http://civic-eg.com/viewtopic.php?t=27660
Sedan(gone) http://civic-eg.com/viewtopic.php?t=7462

- Tue Aug 26, 2014 1:21 pm #348263 I would check the head for any type of imperfection or "ding" in that area. Otherwise look for splits and or cuts in the gasket. You can use a gasket maker but honestly unless you live in BFE far away from a Honda dealer, they should always have a gasket for this on the shelf

1992 Honda Civic SIR-S

- Tue Aug 26, 2014 4:39 pm #348270

I would check the head for any type of imperfection or "ding" in that area. Otherwise look for splits and or cuts in the gasket. You can use a gasket maker but honestly unless you live in BFE far away from a Honda dealer, they should always have a gasket for this on the shelf

I checked all of that. Its just not a good gasket. Its kinda hard rubber compared to the oem one. I just used a thin bead of make a gasket between the gasket and head. Then let it dry over night. Drove to work and no leak. I dont wanna replace it just yet cause im still breaking the engine in. I just changed to full synth. oil. I want to put 500 more miles on and then i will re-set all the valves, New valve cover gasket and repainting the v/c agin. Thanks for the help tho.

Hatch http://civic-eg.com/viewtopic.php?t=27660
Sedan(gone) http://civic-eg.com/viewtopic.php?t=7462

- Thu Aug 28, 2014 2:51 am #348346 Chime back in and let us know how it goes to your engine after oil change, I just looked up on that because it happened to my D15 for a bit.

- Thu Aug 28, 2014 3:19 pm #348350 Im just going to change the gasket. If it still does it then I think my v/c might be twisted I know its nothing with the head. That was sent to a shop and they inspected the whole thing. was in grate shape...

Hatch http://civic-eg.com/viewtopic.php?t=27660
Sedan(gone) http://civic-eg.com/viewtopic.php?t=7462

[suspendedHatch]

- Fri Aug 29, 2014 4:33 pm #348376 Is your PCV or breather box clogged? Did you remove the breather box and clean it out?

- Fri Aug 29, 2014 5:44 pm #348382 that stuff is all good. Its the gasket. It shrunk up and was causing a gap. after i added a bit of liquid gasket, it hasent had any issues. Its crappy aftermarket stuff. Im getting an oem kit.

Hatch http://civic-eg.com/viewtopic.php?t=27660
Sedan(gone) http://civic-eg.com/viewtopic.php?t=7462