Looking to swap(need info)

B16, B18, B20
 Reply

By Swamp_thing
- Fri Nov 26, 2010 10:19 pm #224760 True...My buddy has a B16 in his coupe,and hes makin 532whp...So thts y im thinkin bout doin the swap...And i talked to the tuner who did my previous car,and he said on the proper build,and a good tune,id beable to c my goal.....So I think im goin for it :woot: ...and thnx,ill look for the hydro conversion...Does it justbolt right up?
User avatar

By lsvbeghatch
- Fri Nov 26, 2010 10:26 pm #224761 Not sure just look on hasport.com and they'll have info on it I myself haven't done it but its a honda it can't be too hard lol
User avatar

By asianrob
- Sat Nov 27, 2010 4:51 am #224793 stick to hydro they are soo much better than cable!

By Swamp_thing
- Sat Nov 27, 2010 9:35 am #224827 Would the hydro conversion do it,or should i just try n get the motor,linkage n ecu,n then find a hydro tranny?
User avatar

By lsvbeghatch
- Sat Nov 27, 2010 3:34 pm #224839 If you want to do hydro to cable hasport is where its at if you wanna use the hydro and can get all the stuff plus trans for 500 do it and sell the cable trans to work towards the hydro

By cjw_89
- Mon Nov 29, 2010 9:06 pm #225076 i made my hydro to cable swap.Cost me nothing.dont even need a welder:) heres a few pics i do have.

Image

Image

Btw this wored flawlessly.Used a tie rod end off a ski doo i had laying around.Cant blame me for being creative.This gearbox is now being used for an acura el with a b18 swap.
User avatar

By lsvbeghatch
- Mon Nov 29, 2010 9:38 pm #225083 Wow... very creative lol that's great and its actually functional is what gets me...

By Swamp_thing
- Sun Dec 05, 2010 9:10 pm #226182 I was reading another post,do i need to get a half shaft too off an integra,orcan i use my civics?
User avatar

By Greasedmonkey
- Mon Dec 06, 2010 2:48 am #226217 integra halfshaft and axles.

By Swamp_thing
- Mon Dec 06, 2010 3:29 am #226224 Thanks guys,uhave helped me out ALOT...My buddy is holding the motor for me til X-mas,then its build time for the motor :woot: Another turbo hatch comin to the site soon :D
User avatar

By kapow
- Tue Dec 07, 2010 11:20 am #226467 I done a B16 conversion, the engine was from an EK Sir Civic

So axels from an EK (b16) will work

With engine mounts, in some countrys, you can use both left-right-rear original civic engine mounts, if not, the right one will be different, either it will be 3 post or 2 post

Also you will need either EK B16 gearbox torque mount or 94-01 integra one

By Swamp_thing
- Thu Dec 09, 2010 4:33 am #226859 Thnks for all the help guys...Im pickin up my B16 motor,trans,linkage n ECU after x-mas,most of my money went on my kid,and girlfriend...So ill soon have a B16 :D
User avatar

By kapow
- Thu Dec 09, 2010 8:00 am #226886
Swamp_thing wrote:Thnks for all the help guys...Im pickin up my B16 motor,trans,linkage n ECU after x-mas,most of my money went on my kid,and girlfriend...So ill soon have a B16 :D


aw dude, sounds like you deserve it :)
 Reply
Return to B Series