Page 1 of 2
my motors bogging down
Posted:
Fri Jun 21, 2013 2:23 pmby Squirrelman91
Ok so I just rebuilt my motor and I drove it around the block and first time around it does fine but when the motor starts to get warm I loose all power and starts to bogg down really bad what would cause this [/list]
Posted:
Sun Jun 23, 2013 2:21 amby bks84
What have you checked?
Posted:
Sun Jun 23, 2013 8:57 pmby Squirrelman91
I've checked the map sensor the o2 sensor.will the b18 run on the stock eg computer?.and how do I tell what computer I have?
Posted:
Mon Jun 24, 2013 2:51 amby nd1983
Squirrelman91 wrote:I've checked the map sensor the o2 sensor.will the b18 run on the stock eg computer?.and how do I tell what computer I have?
the b18 needs the b18 computer to run properly. alot ofstuff willl be off, A/F, o2 readings, all the engine components.
Posted:
Mon Jun 24, 2013 11:49 amby Squirrelman91
How do I tell if I have the eg computer or the b18 computer I bought the car with the b18 already swapped so I dont know which one I have
Posted:
Mon Jun 24, 2013 2:21 pmby Fada Blayne
You need a pr4 ecu. Take a look at the ecu you have at the moment and make sure that it is one. You can also run a p75 with a 0db2 to Obd1 convertor harness.
Posted:
Mon Jun 24, 2013 10:38 pmby bks84
p75's came obd1 as well. 94-95 integra rs/ls/gs/"se" whatever trim as long as it has a b18b1 in it.
if your car has the correct ecu pr4 or p75, doesnt matter, then id check calibration on TPS and test coil/ignitor (or if you have a buddy who has a good LS distributor just swap the distributors)
any check engine lights?
Posted:
Mon Jun 24, 2013 11:59 pmby Squirrelman91
Ive replaced the coil and ingitor. I know its not the dizzy my friend thinks its the ecu
Posted:
Tue Jun 25, 2013 12:53 amby nd1983
Squirrelman91 wrote:my friend thinks its the ecu
and his reason? most just don't die.
Posted:
Tue Jun 25, 2013 12:57 amby Squirrelman91
So I just pulled the ecu out and I have the stock 94 PO6. so what do I do??
Posted:
Tue Jun 25, 2013 9:59 amby Fada Blayne
You should obviously swap it for one of the ones mentioned above. Should be a relatively easy find at a junkyard or even craigslist.
Posted:
Tue Jun 25, 2013 4:39 pmby Squirrelman91
My motor is obd2 will the p75 with the convertor work??
Posted:
Tue Jun 25, 2013 5:07 pmby Squirrelman91
My motor is obd2 will the p75 with the convertor work??
Posted:
Tue Jun 25, 2013 9:50 pmby bks84
doesnt matter what OBD your engine is, if its in a 92-95 Civic, then its being ran as OBD1, since they came OBD1.
Have you checked to see what ECU youre currently running? If not, do that. If youre on the wrong ECU it probably wont run well and could be the root of all the bogging, and whatever other problems youre having.
Posted:
Tue Jun 25, 2013 11:46 pmby Squirrelman91
Im running the stock PO6