Page 1 of 2
Will a 92 hatch have enough room....
Posted:
Mon Mar 02, 2009 8:53 pmby Matt.M
Well I was looking at exhausts to put onto my project car when I get it out of the shop from being painted, and was wondering if there would be room for a header after I put a b18b in the engine bay.
Posted:
Mon Mar 02, 2009 9:35 pmby hondajunkee
well not exactly sure what your asking, are you try to see if you'll be able to fit an aftermarket header on your civic with a b18 in it? if that's the question then of course you can without a problem
Posted:
Mon Mar 02, 2009 9:55 pmby RevinEK
yup
Posted:
Tue Mar 03, 2009 2:56 amby Matt.M
Without any fabrication?
Posted:
Tue Mar 03, 2009 8:23 amby chrono404
Possibly on one for a 90-93 Integra. However if you get a 94-01 Integra Header(or aftermarket replacement) it will bolt up with out issue.
Posted:
Tue Mar 03, 2009 9:52 amby Matt.M
Okay, this may sound really stupid, I've never done a swap before, but when I get the other engine in, do I get a header/exhaust from the year of my car now or from the year/make of the engine?
Posted:
Wed Mar 04, 2009 7:20 amby chrono404
any header for a 94-01 integra will work on your car with a B Series swap.
Posted:
Wed Mar 04, 2009 5:59 pmby Greasedmonkey
you will have plenty of room...check it. You will get a header for a B series motor. 99-00 civic Si header will work and reportedly mate up with the exhaust.
header
stock
Posted:
Thu Mar 05, 2009 3:09 amby Matt.M
Okay, thanks a lot guys. So when I get an exhaust, do I need to search '92 civic exhaust' or 'integra exhaust'?
Posted:
Thu Mar 05, 2009 3:20 amby hatchin06
why not go to an exhaust shop and have the make you one?
Posted:
Thu Mar 05, 2009 3:26 amby chrono404
if you where going to buy an exhaust system online, It would be for your car. I.e if you have a 92 Civic hatch you would want to by exhaust for a 92 Civic hatch, if your rocking a Coupe or Sedan then you would get the exhaust for that model.
You could also have an Exhaust shop make your pipe for you.
Posted:
Thu Mar 05, 2009 4:09 amby Greasedmonkey
you get the exhaust for the car. You will have to get it modified though.
Posted:
Thu Mar 05, 2009 5:51 amby Matt.M
I don't know about any place that makes exhausts, especially mandrel bent ones.
Now on for the parts like oil/water pump. With things like that, what year would I need to look up since I'll be using a b20 bottom end and a vtec head that will probably be of different years?
Posted:
Thu Mar 05, 2009 5:57 amby hotrodcivic
ok, my 92 EG has a H22A1 in it and I have no issues, although, you can always do the DYI hood raise.
Posted:
Thu Mar 05, 2009 5:27 pmby Greasedmonkey
Matt.M wrote:I don't know about any place that makes exhausts, especially mandrel bent ones.
Now on for the parts like oil/water pump. With things like that, what year would I need to look up since I'll be using a b20 bottom end and a vtec head that will probably be of different years?
obd1 parts. you would get the water pump and oil pump for a GSR/ITR as well as a timing belt from those cars.