1992 Honda Civic Si [Dyno results]

Post YOUR Hatchback here
 Reply
User avatar

By Sentry
- Thu Mar 26, 2009 3:25 am #105809 Full catback. :)

I actually bought a can of black hightemp yesterday to paint the tip. :lol:

I need to polish it up again before I can paint it though.
User avatar

By Sentry
- Fri Mar 27, 2009 9:13 pm #106180 Image
Image
:hehe:
User avatar

By EgCruiser
- Fri Mar 27, 2009 9:44 pm #106186
Sentry wrote:Installed a fancy snow plow today. :D

Image
Image
Image


You Cant call it a Snow Plow Before you lower that Eg
Your Rims looking Goooooood man :) :D
User avatar

By Sentry
- Sat Apr 11, 2009 9:16 pm #109975 Got my resistor box Friday. Picked up some wiring supplies and got it prepped today. This'll all be in by June. (I have to go away for three weeks :()

I'm going to do the same thing with the MAP sensor, with bullet connectors. That way if a nicer car comes along and I want to return this to stock all I have to do is unplug my stuff and swap it over to the new car. :D

Image

Each plug measured about 6.6-6.8 ohms. Should be good.
User avatar

By Sentry
- Thu Apr 16, 2009 10:52 pm #111103 Installed my intercooler today. Shits very snug. Minimal trimming of the bumper cover was needed, the rest of the pipe fit very nicely.
Image

Had a bit of heat wrap left over, so I threw that over it near the downpipe. Perfect fit. :D
Image

Mmm. Ugly hood. And stealthy. :thumb:
Image

EDIT: 15.21 Gotta put those damn injectors in when I get back on the 8th. :lol:

http://www.youtube.com/watch?v=rL9wRIiRbe8
Last edited by Sentry on Fri Apr 17, 2009 4:17 am, edited 1 time in total.
User avatar

By Gorveatt
- Thu Apr 16, 2009 11:02 pm #111107 Very nice man, looks good. And the exhaust sounds great, sounds alot like the Apexi WS2
User avatar

By Sentry
- Thu Jun 04, 2009 7:47 am #120565 Injectors and MAP sensor are in and wired and I replaced the EPROM chip in the ECU, boost is now at 11psi up from 6psi. Butt dyno approved. ;D
Image
I took off that cheesy lip. Eh, just wasn't me. Put on a junkyard hood to replace the nasty peeling and rusty red one. New mirrors too. EGT gauge to accompany my boost gauge so I wasn't turning it up blindly.
Image
Current bay shot. Little messy, had the splash tray taken off for a couple days back when I installed the intercooler. I didn't feel like putting it back on right away because it meant more damn cutting. :lol:
Image
User avatar

By Sentry
- Sat Jun 13, 2009 12:59 am #122687 Who can guess why I need this. :lol:
Image
User avatar

By chrono404
- Sat Jun 13, 2009 2:27 am #122696 Making to much power your stock shitty clutch is slipping. :thumb:
Had that problem when I was shooting up Nitrous.

Your car is coming along quite well, The Stealth Turbo Install is Clean. Very Nice. :thumb: :thumb:
User avatar

By Greasedmonkey
- Sat Jun 13, 2009 4:47 am #122725 y0 shits made is korea!!
User avatar

By Sentry
- Sat Jun 13, 2009 6:17 pm #122798 As long as it doesn't fly apart it's fine. The pressure plate is the important bit. :D

Clutch is from LSD motorsports.

By EG MIKE
- Sun Jun 14, 2009 3:32 am #122843 wow, snow all the time? Car looks good though man! keep it up!
 Reply
Return to Your Ride - Hatchback