- Thu Dec 01, 2011 6:46 pm
#283656
So I recently joined this site because it has tons of useful info and nice ideas! Here is my EG so far, I guess I can start my build...?
Here we go: (feel free to give me some input or ideas?
)
Car when first purchased
looked like a mess...... in my opinion
Sorry I did not have too many pictures of my car when first purchased or as was doing a lot of the work on the car....
Here is some of the things I took out and also a few things I swapped into my interior:
(NOTE: My interior was Completely stock other than the driver’s side recaro and passenger gsr seat, just didn’t have pics)
removed these seats, I want to eventually put in two Black DC2 recaros!
Put in an ek center console unit:
originally had an SIR cluster:
It had some problems however, so I swapped it with an S2K AP1 cluster:
bought a aftermarket assembled wiring harness:
Here is my interior as of today:
-Replaced the door panel inserts with black synthetic leather and red stitch
-E-brake boot and shift boot were replaced as well to black with red stitch, the shift boot is an Genuine Honda CTR boot.
-The EK console is in place, jut needs to be painted black
-Two front seats were replaced with another pair of GSR seats, saving up for my black DC2 recaros
-S2K cluster with CF bezel (bezel needs some work, this was my first attempt)
-JVC deck with two color tone to match my S2K cluster
-Rear speakers and brackets installed
-I installed a rear window wiper because we need it here in Canada during the winter LOL...
-Pioneer sub in the back
Pics:
As for the exterior:
-Have not done too much so far, it needs lots of work... I have two new bumpers and fenders sitting in my garage, will be doing most of the body work myself in the spring
-Over the last summer I did an ITR 4x114.3 lug spindle swap with ITR 15" rims
-four wheel disk conversion!
(They sent me one wrong spindle.... but it got exchanged in the end!)
JDM B16a swapped in when I bought the car:
engine is in excellent running condition, just needs to be cleaned up a little, and hide the wires better.
Also did a Bi-Xenon HID D2S Mini Projector Retrofit:
old
new
retrofit
clean cut off
here is my fogs after recent installation, 6000K HID bulb with yellow lens to give me a nice lime green light
(bit of a bad picture, the light output is a bit lighter than what is seen here)
now the car as it looks today (winter time...)
Car is lowered with a 1.5" drop on some skunk2 Pro Series coilovers. All bushings have been changed to polyurethane, and I am using some skunk2 LCA's with an ASR bracer. Working on getting some sway bars eventually, but in the mean time this eg feels great on the corners
car still needs lots of body work, and a few more things for the interior... Still my project car, hope you guys will all have some nice inputs?
Thanks for looking!
Here we go: (feel free to give me some input or ideas?
)
Car when first purchased
looked like a mess...... in my opinion
Sorry I did not have too many pictures of my car when first purchased or as was doing a lot of the work on the car....
Here is some of the things I took out and also a few things I swapped into my interior:
(NOTE: My interior was Completely stock other than the driver’s side recaro and passenger gsr seat, just didn’t have pics)
removed these seats, I want to eventually put in two Black DC2 recaros!
Put in an ek center console unit:
originally had an SIR cluster:
It had some problems however, so I swapped it with an S2K AP1 cluster:
bought a aftermarket assembled wiring harness:
Here is my interior as of today:
-Replaced the door panel inserts with black synthetic leather and red stitch
-E-brake boot and shift boot were replaced as well to black with red stitch, the shift boot is an Genuine Honda CTR boot.
-The EK console is in place, jut needs to be painted black
-Two front seats were replaced with another pair of GSR seats, saving up for my black DC2 recaros
-S2K cluster with CF bezel (bezel needs some work, this was my first attempt)
-JVC deck with two color tone to match my S2K cluster
-Rear speakers and brackets installed
-I installed a rear window wiper because we need it here in Canada during the winter LOL...
-Pioneer sub in the back
Pics:
As for the exterior:
-Have not done too much so far, it needs lots of work... I have two new bumpers and fenders sitting in my garage, will be doing most of the body work myself in the spring
-Over the last summer I did an ITR 4x114.3 lug spindle swap with ITR 15" rims
-four wheel disk conversion!
(They sent me one wrong spindle.... but it got exchanged in the end!)
JDM B16a swapped in when I bought the car:
engine is in excellent running condition, just needs to be cleaned up a little, and hide the wires better.
Also did a Bi-Xenon HID D2S Mini Projector Retrofit:
old
new
retrofit
clean cut off
here is my fogs after recent installation, 6000K HID bulb with yellow lens to give me a nice lime green light
(bit of a bad picture, the light output is a bit lighter than what is seen here)
now the car as it looks today (winter time...)
Car is lowered with a 1.5" drop on some skunk2 Pro Series coilovers. All bushings have been changed to polyurethane, and I am using some skunk2 LCA's with an ASR bracer. Working on getting some sway bars eventually, but in the mean time this eg feels great on the corners
car still needs lots of body work, and a few more things for the interior... Still my project car, hope you guys will all have some nice inputs?
Thanks for looking!
Last edited by mitch6 on Mon Jul 14, 2014 11:14 pm, edited 20 times in total.
keep it up
