Civic-EG.com Forum 3.3.1

- Sun Feb 03, 2008 5:49 am #40614 will dash and door panels from an integra sedan fit on a civic sedan?

[chrono404]

- Sun Feb 03, 2008 7:09 am #40630 The Dash fits, I have scene it done a few times. However there is probably alot of Fabing needed to have it done right. Not sure about Door panels though.

If it did that would be killer, it would look very awesome.

2017 Chevy BoltEV DD |2001 Honda CRV SE

- Sun Feb 03, 2008 7:20 am #40631 i seen people do the door panels before they said it fits fine but then again they say the EG panels will fit fine just they have a small gap

Last edited by asianrob on Sun Feb 03, 2008 7:20 am, edited 1 time in total.

92 civic cx sold!!
horizon gray 94 LX-A wrecked :/
white 92 civic Si (traded)
primered 94 teg sold
92 civic DX sold!!
93 red EX coupe parted out!
93 LS400 Midnight indigo sold!
92 civic LX sold!!
90 240sx sold!
93 faded black EX coupe

- Sun Feb 03, 2008 7:20 am #40632 rear 4door integra seats fit the civic sedan.

-LowTEC Derbo "the coupe" Build Thread
http://civic-eg.com/viewtopic.php?t=1589
272whp 214wtq

- Sun Feb 03, 2008 7:24 am #40634

rear 4door integra seats fit the civic sedan.

yup and read that 4door bottoms and 2Dr teg tops work the best in Hatchies

92 civic cx sold!!
horizon gray 94 LX-A wrecked :/
white 92 civic Si (traded)
primered 94 teg sold
92 civic DX sold!!
93 red EX coupe parted out!
93 LS400 Midnight indigo sold!
92 civic LX sold!!
90 240sx sold!
93 faded black EX coupe

- Sun Feb 03, 2008 7:29 am #40636 hahaha i already have eg9 seats for mine.
i want to do something different with dash and door panels though.

- Sun Feb 03, 2008 8:03 am #40641 ok, so i found a write up on fitting the dash and it can be done.
now i need to find out if the door panels fit cause i don't feel like cutting up my stock panels.

http://honda-tech.com/zerothread?id=1211255

[ohDirka]

- Sun Feb 03, 2008 9:09 am #40650 heres one for the dash http://honda-tech.com/zerothread?id=285567

Race cars are like boats I guess. Time to bust out another thousand.

- Sun Feb 03, 2008 9:17 am #40652 yeah pretty much the same as the one i found.
the thing is i don't want to cut up the eg door panels just so they fit.
they look like shit.
my brother has a wreck integra, the thing is it's a coupe and i have a eg sedan.
i don't want to buy integra door panels and not be able to make them fit.

- Sun Feb 03, 2008 10:25 am #40654 i found a coupe with dash and door panels.
i think i'm just going to go for it and try the sedan panels
http://www.clubcivic.com/board/showthread.php?t=91189&highlight=integra+door+panels+civic

- Sat Feb 09, 2008 1:13 am #41516

i found a coupe with dash and door panels.
i think i'm just going to go for it and try the sedan panels
http://www.clubcivic.com/board/showthread.php?t=91189&highlight=integra+door+panels+civic

You don't have to cut up the civic panels to make the dash fit, you can heat the panels up and then slam the door shut and the civic panels mold to the integra dash and will fit flush w/o any hacking of the civic panels.

- Tue Mar 04, 2008 9:15 pm #44771 yeah but if you do that they will look like shit. Your best bet is to pull th skins of your door panels, after the dash is installed and install door panels line them up make a line were they are going to fit cut panels and have them recovered.

Last edited by sfixed on Tue Mar 04, 2008 9:17 pm, edited 1 time in total.

- Tue Mar 04, 2008 9:16 pm #44772 yeah but if you do that they will look like shit. Your best bet is to pull th skins of your door panels, after the dash is installed and install door panels line them up make a line were they are going to fit cut panels and get then have them recoverred.